Netgear EX3700 setup

A leading supplier of networking solutions, Netgear, addresses this issue with the Netgear EX3700 Setup, a powerful WiFi range extender that will eliminate dead zones and fortify your existing network.

Netgear EX3700 setup Configuration

At first, take out the Netgear EX3700 WiFi extender’s box first.
Then use your device for linking to its network.
If asked, enter the default credentials.
Enter “mywifiext.net” in the address bar of an open web browser.

Observe the directions on screen.
At the same time, enter your login credentials by default.
Set up your extender’s network name and password, among other settings.
Similarly, set the extension halfway between the weak WiFi region and your router.
Expand the coverage and get the maximum network strength with the appropriate setup.
Hereafter, your Netgear EX3700 is prepared to improve coverage by expanding the range of your WiFi.

Netgear EX3700 setup via manual method

Once the Netgear EX3700 WiFi extender has been unpacked, plug it into a power outlet that is close to your current WiFi router.
Then, check if the extender is on.
At the same time, hold off until the solid green power LED turns on.
Afterward, using a WiFi-capable device, join the “NETGEAR_EXT” default WiFi network.
Then use the default credentials to log in.
Similarly, to establish WiFi settings, including network name and password, follow the on-screen directions.
Try to put the extender at the place where it can cover all the dead zones.
At the same time, your Netgear EX3700 is prepared to expand your WiFi network.

Netgear EX3700 setup via WPS method

At first, make sure the router you have is WPS compatible.
Then, use a physical WPS button or the router’s settings to enable WPS on your network.
Subsequently, to expand your WiFi signal, plug the Netgear EX3700 power outlet into a power outlet that is near your router.
Afterward, press the extender’s WPS button.
The WPS LED ought to begin to flicker.
At the same time, press your router’s WPS button after two minutes.
The extender’s WPS LED will glow solid to show that the connection was made successfully.
At last, to get the best WiFi coverage, move the extender if needed.

AC750 wifi range extender setup

In the first place, plug the Netgear AC750 WiFi Range Extender Setup (EX3700) into a power outlet close to your current WiFi router after unpacking it.

Then, make sure the extension is turned on, then watch for the solidification of the power LED.
Afterward, make use of a gadget to link to the WiFi network of the extender (network name by default: NETGEAR_EXT).
By the time, go to web browser and paste its address to search.
Then, use the default credentials to log in.
Subsequently, to successfully increase your WiFi range, position the extender for best coverage.
At last, finalise the configuration, and your Netgear AC750 EX3700 is prepared for improved WiFi coverage. This completes the setup.

Netgear AC750 Wifi Range extender model Ex3700 Setup

Take the Netgear EX3700 AC750 WiFi Range Extender out of its packaging and connect it to a power outlet close to your current router.
Turn on the extender and wait for the power LED to solidify, which will signal that it is ready.
Make a connection to the WiFi network of the extender using a device
Launch your browser, then go to “www.mywifiext.net.”
Use the default login information to log in, then follow the on-screen directions to set up network name and password, among other options.
After completing the configuration, the Netgear EX3700 AC750 is prepared to improve the coverage of your WiFi.

Netgear EX3700 setup common issues

Make that the extender is within the router’s coverage area.
If necessary, move it closer, and make sure the router is operating properly.
Placement must be ideal.
For optimal coverage, position it halfway between the dead zone and the router, keeping obstacles to a minimum.
Delete your browser’s cache or switch to a different one.
Make use of the default login. Reset the extender to its original configuration, if altered.
Verify that WPS is supported by your router.

Make sure the router and the extender have the WPS function turned on.
Recognise LED lights appropriately.
Blinking signals a problem, while solid green shows a successful connection.
For troubleshooting, refer to the handbook.
For updates, go to the official Netgear website.
Verify if the 2.4GHz and 5GHz WiFi bands on the extender are supported by your devices.
Reduce interference from other electronic devices as much as possible, and change the WiFi channel.

Netgear EX3700 Setup troubleshooting tips

For optimal coverage, place the EX3700 halfway between dead zones and the router.
Turn on the extender by plugging it in and watching for the solid green LED signal to appear.
From your device’s WiFi settings, join the “NETGEAR_EXT” network.
To access the Netgear EX3700 setup wizard, open a web browser and type “mywifiext.net”.
During the setup procedure, if necessary, create a Netgear account.
From the list, select your current WiFi network, then type the password.
To change settings or stick with the defaults, follow the on-screen directions.
Click “Finish” to terminate the setup procedure and restart the extender with the updated configuration.

Netgear EX3700 setup firmware update

Access the setup page of the extender by logging in to “www.mywifiext.net.” Please take note of the firmware version.
Visit the official Netgear support website and select the EX3700 product page.
Find the most recent firmware update for the model of your extender.
On your PC, download the firmware file.
Go back to the configuration page of the extender and register.
Give the firmware upgrade procedure time to complete.
This may require a reboot of the extender.

MYWIFIEXT